piling rig for guardrail
Home

Highway barrier post ramming unit

Highway barrier post ramming unit

  • Which Guardrail Post Driver Should You Choose? Crawler, Wheeled, Truck and 2-in-1 Compared
    Nov 18, 2026
    Anhui TeZhong Machinery Technology Co., Ltd. builds road barrier machines in six configurations: a 39 kW wheeled driver, the 39 kW TZ390 and TZ390T with driving, pulling and drilling in one chassis, the 39 kW TZ530 and TZ530T rotary drills, a 75 kW crawler with GPS and automatic levelling, and an 85 kW truck-mounted unit. Pile driving height runs from 3.0 m to 4.15 m, drilling depth from 1.7 m to 3.5 m, and drilling diameter from 50 mm to 300 mm, or Φ155–230+ on the rotary models. Those are ratings for named machines, not a promise of posts per hour: the longest reach belongs to the truck, the deepest hole to the crawler, and the on-board compressor to the TZ390T and TZ530T. Our highway barrier post ramming unit line is built by a direct manufacturer and OEM supplier in Suzhou, Anhui. Figures current as of 18 November 2026. Quick Answer: six formats, three power classes, two separate reach limits Most machines in this range run at 39 kW and drive to 3.0 m with a 2.2 m drilling depth and a 50–300 mm hole range. Move up and the numbers split: the TZ650 crawler runs 75 kW with 4.0 m driving and 3.5 m drilling, while the truck-mounted unit runs 85 kW with a 4.15 m driving height but only 1.7 m drilling depth. As of 18 November 2026, no single configuration leads on both reach and hole depth. Anhui TeZhong Machinery Technology Co., Ltd. builds all six, and the signed configuration sheet — not the headline power figure — decides what goes on the truck. Figure 1: Driving height and drilling depth are different limits. The truck reaches highest; the crawler drills deepest. 3.0–4.15 m Pile driving height 1.7–3.5 m Drilling depth 39–85 kW Rated power range 50–300 mm Drilling diameter range Table of Contents Which machine formats are available for roadside post installation? What do the 39 kW machines actually do? When does the 75 kW crawler make sense? What changes on a truck-mounted post driver? Why do some road crews drill before they drive? What does an on-board compressor change? What did a highway crew order and then reorder? What should you put on the RFQ before we quote? FAQ Which machine formats are available for roadside post installation? Six configurations cover four chassis formats. Put the numbers side by side and the pattern is clear: 39 kW is the standard class, while the 75 kW crawler and 85 kW truck each buy one specific advantage. Configuration Power Driving height Drilling depth Hole diameter Distinctive item Wheeled driver 39 kW 3.0 m 2.2 m 50–300 mm Hydraulic hammer, drives and pulls TZ390 39 kW 3.0 m 2.2 m 50–300 mm Four attachment modes TZ390T 39 kW 3.0 m 2.2 m 50–300 mm On-board KSCY-330/8 compressor TZ530 / TZ530T 39 kW 2.2 m screw pile 2.2 m Φ155–230+ Rotary drill; TZ530T carries air TZ650 crawler 75 kW 4.0 m 3.5 m 50–300 mm GPS, auto levelling, auto control Truck-mounted 85 kW 4.15 m 1.7 m 50–300 mm China Stage IV, ≥100 km/h travel What do the 39 kW machines actually do? The TZ390 is built as a four-mode platform: pile driving and pulling, screw pile driving, auger drilling and impact drilling. It does all of that on 39 kW, with 3.0 m driving height, 2.2 m drilling depth and a 50–300 mm hole range. The wheeled road driver sits in the same power and reach class with a hydraulic hammer and pulling function. Neither is a one-job machine. The TZ530 changes the emphasis from driving to drilling: 2.2 m screw pile driving, 2.2 m hole depth and discrete diameters of Φ155, 180, 185, 200 and 230+ mm. If your crew spends more time opening holes in rock than striking posts, that is the family to start from. If it mostly sets posts on a clear shoulder, the 39 kW driver is enough and the extra rotary head is money parked on the trailer. When does the 75 kW crawler make sense? The TZ650 is the only tracked machine in this line and the only one with GPS, automatic levelling and an automatic control system. Power comes from a Cummins 4BT3.9-C100 rated at 75 kW. It drives and screw-piles to 4.0 m, drills to 3.5 m, covers 50–300 mm holes, and switches between piling, pulling, screw pile driving and auger drilling. That combination earns its keep on ungraded or sloped shoulders, where a wheeled unit has to be levelled by hand and every post costs a few more minutes. The same 4.0 m reach and 50–300 mm hole range also suit ground-mount PV work, which is why this chassis appears in both product lines rather than being forced into one category. What changes on a truck-mounted post driver? The truck unit is the reach and travel specialist: 4.15 m pile driving height, 85 kW, China Stage IV emissions and a maximum travel speed of at least 100 km/h. It installs posts by impact and ramming, then sets the rail structure behind it. The trade-off is explicit — drilling depth drops to 1.7 m, against 3.5 m on the crawler and 2.2 m on most 39 kW machines. Contractors covering long route sections, or running emergency barrier repair, buy the road speed and the extra reach. Check which emission class the tender accepts before you commit to the 85 kW option; the machine we list is China Stage IV, and that is a specification, not a formality. Why do some road crews drill before they drive? Because a post driven straight into hard rock refuses to reach depth. In rock that is hard to very hard, or where the line crosses large boulders, the hole is opened first and the post is set after. Our rock-capable road machines list 110, 152, 178 and 200 mm drilling diameters, inside the wider 50–300 mm range, on a 39 kW chassis with 3.0 m driving height and 2.2 m drilling depth. When the hole has to go deeper than any roadside rig reaches, the work moves to a percussive rock drill rig: six models rated to 30 m, 35 m and 50 m with 90–500 mm hole diameters and 10–50 m³/min air demand. Road crews and quarry crews share the same geology; what differs is the depth of the hole and how often the machine has to move. What does an on-board compressor change? Two machines in the range carry their own air: the TZ390T and the TZ530T, both fitted with a KSCY-330/8 compressor. On the TZ390T that unit sits alongside a hydraulic hammer and a rotary head, so the operator can drive, pull and drill without changing the attachment. The TZ530T is the drill-first version, with the same 39 kW rating and built-in air. The other configurations take air from a separate machine, which is fine when a site already runs a compressor and several drills. We also supply diesel screw compressors as a separate line, listed from 110 to 1200 cfm. Matching air supply to the tool matters more than matching it to engine power, and the pair should be written on the same sheet as the machine. What did a highway crew order and then reorder? A customer in Kazakhstan placed an order for four high-speed roadside units in 2024, tested them thoroughly on site, and came back for ten more after the crew reported stable, fast installation. That second order tells us more than any catalogue claim: once a road crew has run a machine through a real lane-closure window, it either asks for another or it does not. As a factory we list a monthly capacity of 500 machines, CE and ISO9001 certification, one-year machine warranty with three months on electrical parts, and payment by T/T or 100% L/C at sight. We quote the same terms to a wholesale distributor as to an end user. Our engineers will not promise a posts-per-shift figure for ground they have not seen — the honest answer starts with the five items below. What should you put on the RFQ before we quote? Send this What it fixes Post profile and required driving height 3.0 m, 4.0 m or 4.15 m class Ground condition and whether rock is present Hammer only, auger pre-drill, or a deeper rock rig Hole diameter and depth 50–300 mm, Φ155–230+, 1.7 m / 2.2 m / 3.5 m Chassis and distance between sites 39 kW wheeled, 75 kW crawler, or 85 kW truck at ≥100 km/h Air already available on site KSCY-330/8 on board, or a separately sized compressor Road and PV sites often share the same 50–300 mm hole range. Where a road crew stops at the post line, a PV pile driving unit continues along the array rows; the TZ536 handles 50–400 mm piles up to 5.5 m. Send the five items and we will answer with a model, its specification table and a written configuration sheet. FAQ Which machine drives the tallest post? The truck-mounted unit, at 4.15 m on 85 kW, with China Stage IV emissions and at least 100 km/h travel speed. Its drilling depth is only 1.7 m. The TZ650 crawler drives 4.0 m but drills to 3.5 m, so the two are not interchangeable. Can one machine drive, pull and drill without changing attachments? Yes — the TZ390 covers pile driving and pulling, screw pile driving, auger drilling and impact drilling on 39 kW, with 3.0 m driving height, 2.2 m drilling depth and a 50–300 mm hole range. The TZ390T adds a rotary head and a KSCY-330/8 on-board compressor. Do these machines need a separate air compressor? The TZ390T and TZ530T carry their own KSCY-330/8 unit. Other configurations take air from a separate compressor, and we supply diesel screw compressors in a 110–1200 cfm range. Size the air supply to the tool and confirm the pairing on the signed configuration sheet.
    Read More

leave a message

leave a message
If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
submit

Our hours

Whether it is a holiday or a festival, we will have someone to receive you 24 hours a day and respond to you in the shortest time.

Contact Us: jennifer@tzpilemachine.com

home

products

WhatsApp

CONTACT US

Need Help? Chat with us

Start a Conversation

Hi! Click one of our members below to chat on